베가스카지노＼＼【【AKR843.C0M】】＼＼베가스카지노
베가스카지노＼＼【【AKR843.C0M】】＼＼베가스카지노베가스카지노＼＼【【AKR843.C0M】】＼＼베가스카지노베가스카지노＼＼【【AKR843.C0M】】＼＼베가스카지노베가스카지노＼＼【【AKR843.C0M】】＼＼베가스카지노베가스카지노＼＼【【AKR843.C0M】】＼＼베가스카지노베가스카지노＼＼【【AKR843.C0M】】＼＼베가스카지노베가스카지노＼＼【【AKR843.C0M】...
View ArticleAD8280 - Hysteresis on OV, UV and OT Trip Points
Hello, I'm using the AD8280 in a Lithium Polymer Battery Pack Monitoring System as safety device (together with the AD7280A device used as main monitoring device).While testing the system functionality...
View ArticleCan I use the ADP1872 to design a bidirectional converter?
The ADP1872 is synchronous buck controller. Theoretically, synchronous buck converters can be used as bidirectional converters. So keeping that in mind the ADP1872 should also be bidirectional (i.e it...
View ArticleADP1853 power-up simPE model
Hello. Do you have power up simPE model of ADP1853?ADP1853 simPower don't have export menu of start-up And I tried to make start-up model using the export SimPower model, but didn't go well. I want to...
View ArticleClik here to view.
Error in recommended +/- rails monitoring circuit from ADM12914-2 datasheet?
Hi, I've selected ADM12914-2 to monitor +15V and -15V supply rails of an ADC board prototype. I used the recommended configuration by Figure 25 from datasheet, Using the design process recommended in...
View ArticleAD8280 - Hysteresis on OV, UV and OT Trip Points
Hello, I'm using the AD8280 in a Lithium Polymer Battery Pack Monitoring System as safety device (together with the AD7280A device used as main monitoring device).While testing the system functionality...
View ArticleSEPIC Design
I am Juliano K. Cioffi, and I am FAE from Brazil. I have been to the last training in Dublin where I could meet the tool. Congratulations for all your work, it is very useful for us to point solutions...
View Articleadspbf518-ezk the vddflash??
the schemic of the adspbf518-ezk gives the vddflash 1.8v,which i find that the datasheet of 518 describe it as the min 2.7v to nominal 3.3v,so is this right?using 1.8v ?
View ArticleEval-ADP1621 Iout(load limit) to 4A
Hi, Any simple tweak that I can do to increase the Maximum Load limit from 2A to 4A for this eval board ? Understand the board can support up to a current limit of 4A except SSA33L Diode, so by...
View ArticleADM1278 operation
Ren When I used 12V for ADM1278 and without EN pin. But I can read ADM1278 register information via I2C bus.Is it normal operation behavior for ADM1278?I don’t want to get any I2C ack from ADM1278 if I...
View ArticleADR03 Vout adjustment range
Hi All, One of my customers has one problem with ADR03 output adjustment range.Part of his circuit schematics is attached.As shown in the schematic, Vout adjustment circuit is almost the same as shown...
View ArticleADP5023 - ADIsimPower Simulation Tool
Hello, My name is Meir and I am DFAE from Phoenix technologies in Israel. One of my customers would like to simulate the ADP5023 by using the excell based ADIsimPower simulator.As I understuood, the...
View ArticleClik here to view.
How can I use the ADP5090 with a CdS cell?
Hello, I'm wanting to use the ADP5090 in a solar powered outdoor light. I'd like to make this as simple of a system as I can to keep cost down and efficiency high. I'd like to use a CdS cell as the...
View ArticleSEPIC Design
I am Juliano K. Cioffi, and I am FAE from Brazil. I have been to the last training in Dublin where I could meet the tool. Congratulations for all your work, it is very useful for us to point solutions...
View ArticleClik here to view.
Error in recommended +/- rails monitoring circuit from ADM12914-2 datasheet?
Hi, I've selected ADM12914-2 to monitor +15V and -15V supply rails of an ADC board prototype. I used the recommended configuration by Figure 25 from datasheet, Using the design process recommended in...
View ArticleClik here to view.
Problem with ADP5024
Hi,I have designed a PCB with Altera Cyclone IV GX FPGA, ADI's AD7626 ADC and some other components. I used ADP5024 regulator for powering the FPGA. I followed the recommendations given by the...
View ArticleADP5024: How to connect an unused Buck regulator
Hello, I was unable to find an answer to this in the datasheet... how should I connect the following ADP5024 pins if I do not want to use the second Buck regulator? VIN2, VOUT2, SW2, FB2, PGND2...
View Article3.3v from ADP5090 + single-cell li-ion?
is it possible to drive a 3.3V load from an ADP5090 with a PV cell and a single-cell li-ion battery? I'm looking at VBAT_SD = 2.7V, VBAT_TERM = 4.1V, so BAT is going to swing above and below 3.3V. do i...
View ArticleADP5071 EVB Board Gerber
Dear All:I need to reference ADP5071 EVB Board PCB Layout design, can give me ADP5071 EVB Board Gerber File reference? thanks~ Best Regards,Cuttlefish
View Articlewhat's the best way of selecting resistor divider values for ADM2914/ADM12914?
it's hard to find the right value resistors for three resistor divider.
View Article