How to add part to the library folder of ADIsimPE simulator?
I just started using ADIsimPE.I want to add AD8335 Pspice model of this part.I found the Pspice mode with .cir in the website. How to add this to the components library of the simulator?
View ArticleADP5588 and multiple keypress / stuck key detection
Hello, I am wondering if anyone has more information regarding what the ADP5588 io port expander / keypad matrix device will do in the event of a stuck key (single or multiple). The datasheet says:...
View ArticleADuM4223
Hi all,I'm currently trying to designo full bridge converter using AD4223 as isolated gate driver. I just find some explications in the link below.https://ez.analog.com/message/165762#165762 But i...
View ArticleClik here to view.
ADP161x For TFT LCD Bias Supply App.
Dear All:ADIhaveprovide "ADP161x TFT LCD Bias Supply" ADISimPower excel file to me simulation? Best Regards,Jackey
View ArticleADM1191 returns wrong values of voltage and current
Hello.I use ADM1191 as a power meter (voltage and current) for motor control application. I init IC to continious convert both voltage and current, or voltage only, or current only. MCU reads values by...
View ArticleADN8831 issue (probably with supply voltage drop)
Hello to all We are trying to use an ADN8831 to drive a TE-module with up to 4V/4A, but it always turns off at ~3A (!standby-pin going low).The circuit we're using is more or less the same as the eval...
View ArticleADN8831 FET Requirements
Hi, I am trying to choose the MOSFETs for ADN8831, but for better efficiency I would like to use ones with lower R_DS,ON than the one suggested in AN-695. Can I use the guideline given in "External FET...
View ArticleADP3338 - 5V output with 0V input
I'm designing a system for a car with two use cases. In normal operation, the system is powered by the 12V car battery, which is regulated to 5.6V by a buck-boost regulator and then to 5V by the...
View ArticleAMP Noise Analysis
Hi, I want to use ADIsimPE to do the noise analysis, after configure some parameters in "Choose Analysis" as below plot and run the simulation, an error is displayed to say "unknown input source 'V3'...
View ArticleClik here to view.
ADN8831 problem
Hello to allI have some problem about adn8831.We use adn8831 to control a TEC of pump laser. But PWM waveform does not appear in the pin 19 and pin 21.Also the Votage on the pin14 is 0.1V. It's seems...
View ArticleADN8831 Cooling Problem
I recently started testing my ADN8831-EVALZ board for its heating and cooling control ability.I am currently using a 10k NTC thermistor. I can successfully heat the target device. However, when I try...
View ArticleOutput filtering for the output ripple noise in ADP5050
Hi All, We are checking at the feasibility of using ADP5050 Integrated Power Solution in our card. Please below find the requirements which are to be generated through its 4 channels. We have a...
View ArticleMOSFET driver without isolation for half-bridge topology
Hi, I'm looking for MOSFET driver of ADI without having isolation function for half-bridge topology. For example using ADP3654, do you have any example circuitry showing how does it connect to half...
View ArticleClik here to view.
Noise analysis
I am using ADIsimPE to simulate an 1st order filter using a AD8646. I am interested in the output noise, but I am having problems making the simulator work. I have followed the instructions in "Help"...
View Article[ADP2370] BLIP board is not ADP2370 evaluation board.
Hi.I got a wrong information from our Disti FAE.about ADP2370 product...
View ArticleUsing AD7280A to stacked voltage cell measurement in electrolyzer?
Hello,Dear Friends, I want to design a circuit to measure individual cell voltage in electrolyzer system.Electrolyzer consists of 170 stack cells (voltage of each cell: 1-5V, Total...
View ArticleClik here to view.
Help debug ADP2370 (fixed 3.0V) but getting 1.6V out
Hi,This is the schematic and just today we got our board and after soldering the buck converter(ADP2370-3.0V) I was surprised to see 1.6v across the capacitor (C1) while I was supplying clean 6.0V DC....
View ArticleClik here to view.
ADP5090 output power rating
Hi May I know the power rating for ADP5090-2-EVALZ that is a Evaluation Board with Solar Harvester ??if we setting 3.3Vout , how much the iout ??
View ArticleADP1047 using for DC/DC
Hello, could the ADP1047 be used for DC/DC design? I want to design a SEPIC controller like this one: http://www.analog.com/static/imported-files/application_notes/AN-1126.pdf The requirements are as...
View ArticleEVAL-ADP5090-2
Hi, Eval-ADP5090-2 is an energy harvesting demo platform based on solar energy harvesting. I am wondering if there is any energy harvesting demo platform based on RF harvesting instead? The application...
View Article