ADP1055 Evaluation Board For 7.4KW Solution
Dear Sir:ADP1055 Evaluation Board now only have input 38-60VDC,output 12V, 20A specification,ADI will propose provide input 400VDC,output 60V, 125A DC-DC Digital Power total solution? I am very...
View ArticleADP5023 - ADIsimPower Simulation Tool
Hello, My name is Meir and I am DFAE from Phoenix technologies in Israel. One of my customers would like to simulate the ADP5023 by using the excell based ADIsimPower simulator.As I understuood, the...
View ArticleADN2830 Monitor Photodiode Current
Dear Sir,While using ADN2830, we found the PD current from laser is lager than 2000 uA. However, the photodiode current ADN2830 can receieved is less than 1200uA. Than, how can we use the ADN2830 to...
View ArticleClik here to view.
ADP5054 CH1/CH2 Parallel Output Schematic
Dear All:I follow up ADP5054 datasheet Rev. PrD Page 14 "parallel operation" process to design ADP5054 schematic. I need CH1/CH2 parallel output Total 12A,Can you help me check this schematic is...
View ArticleWhat changes require to trim the voltage as ADP5050 output voltage tolerance...
Hi all, In the datasheet of ADP5050 it seems that its output voltage tolerance is around 7.5% at 60% step transient. Please clarify does this mean that output voltage of all channels might have...
View ArticleADUM5010 datasheet
Hi, I have things to confirm regarding ADUM5010 datasheet. ADUM5010 looks to be certificated UL1577 by a document in the ADI's web as below....
View ArticleBUCK and LDO which are not used in ADP5052 are safely set to disable.
Dear all, Currently, my customer uses ADP5052 with FPGA. They may not use a part of BUCKs or LDO.How is PIN for BUCK and LDO which are not used handled? Please tell me the manners of setting these to...
View ArticleComponents not found in the new 7.20 ADIsimPE version
I run a simulation using a circuit that was fine with the previous version od ADIsimPE.Now I get a couple of error messages stating that a Mosfet (IRF630) and a core materila (N87 used in a pulse...
View ArticleParallel outputs of ADM7172 for increased output current?
Need 3A for a very low noise RF amplifier. The ADM7172 would be perfect if it had greater output current. Can I parallel the outputs of 2x ADM7172 via small (i.e. 10 mOhm) resistors?If so, what size...
View ArticleADP1048 question
I designed the ADI ADP1048 into a 500W LED light. VIN: 85 – 264VAC; 120 – 340VDC The system works well except when it comes to input voltage transients. The output voltage wiggles causing light...
View ArticleClik here to view.
ADM7150 increase output voltage
Is it possible to increase the ADM7150 output voltage to 12V using this kind of circuit?will the output noise increased?what is the max and min value of r1 and r2 can be used?
View ArticleClik here to view.
ADP2108-3.0 output at 1V
Hi, I have the same situation as several other posters with an ADP2108-3.0 whose output sits at about 1V. With the output at 1V, my circuit is drawing about 45 mA. I have added a 4.7 uF X5R 0603 input...
View ArticleADP5071 Design tool
hi sir I want to design the adp5071 & adp7182,adp7142 for ADCDoes ADI Support the design tool?thanks
View ArticleDesign with ADP2325
Hello, My name is Meir and I am DFAE at Phoenix technologies in Israel. Silicom, one of my customers, started to evaluate the ADP2325 and ADP5023.They are using the ADIsimPOWER and we have some...
View Articleany suggested footprint for ADP198 (LFCSP package = CP-8-10)
I found a suggested footprint for package CP-8-8 (very close to the CP-8-10) but there's no footprint PDF for the CP-8-10 (used on ADP198). My thougth was to modify the CP-8-8 footprint, making the...
View ArticleADN2830 Monitor Photodiode Current
Dear Sir,While using ADN2830, we found the PD current from laser is lager than 2000 uA. However, the photodiode current ADN2830 can receieved is less than 1200uA. Than, how can we use the ADN2830 to...
View ArticleNoise analysis
Hi there, I just started using ADISIMPE recently and I have a question about noise analysis.I tried to check output/input noise of the amp circuit. But the result of the graph is pretty wired.The...
View ArticleADM1278 address setting
Hi , RenI would like to try a circuit for Address pin control due to my system have ADM1278-2ACPZ by each boards. I hope it can define the address by itself. Do you have experience for this kind of...
View ArticleADP5071 Design tool
hi sir I want to design the adp5071 & adp7182,adp7142 for ADCDoes ADI Support the design tool?thanks
View ArticleIs there any difference between ADIsimPE and Pspice model?
Hi! Is there any difference between ADIsimPE and Pspice model?I want to know if I simulate ADIsimPE and Pspice(with macro model),will the result be different thing. I can understand that if use...
View Article