Clik here to view.
Recommendations to connect OrinfFet to ADP1046A
Please tell me how to connect OringFET?If you plan to put in OringFET negative wire.
View ArticleADP5090(quiescent current and sleeping cuurent)
HI all I was going though the datsheet of ADP5090. I got confused with the specs given in datasheet i.e. operating quiescent current of sys pin i.e.320nA(typ) and sleeping quiescent current of sys pin...
View ArticleADP323 - Fall back connection
Hello, My name is Meir and I am DFAE. Sensible Medical, one of my customers, is interested in ADP323 for medical application.They would like to connect 2 LDO modules in parallel, and one of them will...
View ArticleADM1270 Issue
hi sir I want to design the ADM1270 in my system, but I have two issue need to clarity before layout Q1.ADM1270 use the PMOS to be the switch, but PMOS cost Which expensive than NMOS, Why ADI use...
View ArticleNo Linux tools ???
Is there something like ADIsimPower available based on open source tools i.e. for Linux and LibrCalc?
View ArticleADP1055 Evaluation Board For 7.4KW Solution
Dear Sir:ADP1055 Evaluation Board now only have input 38-60VDC,output 12V, 20A specification,ADI will propose provide input 400VDC,output 60V, 125A DC-DC Digital Power total solution? I am very...
View ArticleNo Linux tools ???
Is there something like ADIsimPower available based on open source tools i.e. for Linux and LibrCalc?
View ArticleADN8831 issue
Hello to all.We are making new design with ADN8831 and we have problem how to determinate R and C for PID In laboratory we connect to our system laboratory TEC driver THORLABS TED4015 – this device is...
View ArticleADP198 Reverse Polarity Protection
Inquiry from customer wanting to better understand the ADP198 reverse polarity protection: The ADP198 is used with 3.3V at the input and would like to apply a 5V at the output and activate the reverse...
View ArticleADP1048 for 2kw solution
xudong We would like to design 2000W PFC for motor application base on ADP1048. Do you have any design report for reference ? Like industance ? Mosfet ? ....etc all of key parameter !! Thanks so much ~
View ArticleClik here to view.
2015080- Anveshan 2014
I m trying to simulate this circuit in ADIsimPE. But i m getting the following error. "*** ERROR *** Cannot find DC operating point - No convergence in pseudo transient analysis" what does this error...
View ArticleADP2441 Evaluation Board Gerber
Dear Sir:I want to try follow ADP2441 EVB Board to design my PCB layout, can give me ADP2441-EVALZ EVB Board Gerber File to me reference? thanks Best Regards, Jacky
View ArticleWith regards ADP505x Layout Design
Hi , With regards to ADP505x PCB layout Design . Do you have any reference layout for 2 Layer PCB .What are the best option for 2 Layer PCB design if Thermal Performance for ADP5050x is 75 to 85...
View ArticleADP2386 EMI B
hi Sir Does the ADP2386 EVB passed the EMI?or have any report for the EMI?THANKS@@
View ArticleHow to configure the digital filter of ADP1051?
It is very flexible to configure the digital filter by the use of ADP1051 GUI. By pulling up the low frequency gain in GUI, the low frequency gain is increased. By pulling down the low frequency gain,...
View ArticleADN8831 for 16V/24A TEC?
Hi, I am looking for an TEC controller wich can drives 16V and 24A. I found ADN8831 and now I am asking myself, can I use this driver? Perhaps somebody can give me an advice. Best regards,Jürgen
View ArticleADN8831 FET Burns Out
We are having a problem with our Analog Devices ADN8831 TEC driver circuit. The symptom is we lose TEC lock. 1. We have been using this circuit successfully for 4 years on 3 different line cards.2....
View ArticleADP1712 Enable Pin Management
I am considering the use of the ADP1712 (+3.3V output) to power the ADIS1620x devices in a reference design. The ADIS1620x works best when its start-up waveform resembles a linear ramp that moves from...
View ArticleADP5054 Reference Design& ADISimPower
Dear All:I 'm interested ADP5054 and Into H/W Design. Can you provide ADP5054 EVB Board Schematic/PCB Layout/Gerber & BOM list to me? another ADISimPower EXCEL file ADP505x can't supply ADP5054...
View ArticleClik here to view.
ADP1048 PWM timing registers
Hello, Could you elaborate on a function of PWM rising edge timing(0xFE0C) and setting(0xFE0D) registers?I don't understand its function from only description on ADP1048 datasheet. Best Regards,Mack
View Article