Could I have AD8250 model file?
HiI want to do the simulation of AD8250.I made the model from "AD8250.cir" file.But I couldn't simulate that.Error message is below. *** ERROR *** The circuit is too large to simulate with this...
View ArticleClik here to view.
Simulation using AD8336, AD736 and AD8551 spice models in Pspice
I have this circuit to be simulated in Pspice. I'm a complete newbie to it. But so far have managed to make the schematic (adding external components, which were not available already in the...
View ArticleAD8000 model
ADIsimPE ver14.0.0.162 doesn't contail AD8000 model.Could you provide AD8000 model? Regards,Y.Ishii
View ArticleIn trouble simulating IN-AMP
Hi there,I'm in trouble to simulate IN-AMP, AD623.I'd like to check transient analysis, but for some reason the output of AD623 does not work....There is the error message,"Device AD623 found in...
View Article.step file (or .iges) for ADP7102
"Ultra librarian" (boy, does this UI need a complete re-do), produces a 2D dxf (despite selecting 3D). When I try to export the STP/STL model, I get Component "ADP7102ARDZ-R7" renamed to...
View ArticleADM1166 Programmable Driver Output(12V charge-pump output) is not coming for...
Hi, I am using ADM1166 for monitoring & sequencing the supplies in my board. All the charge pump output of the ADm1166 i.e. PDO1 to PDO6 should give a output voltage of 12V. PDO1 to PDO5 is giving...
View ArticleLinear regulator models?
I also posted this question here: Where are the linear regulators in ADIsimPE? I am interested in simulating some linear regulators including the ADM7154, ADM7150, ADP7182, and ADP1740/1741. So off I...
View ArticleADP1051 CS2 analog offset trim
Hi Sir: 1\how many bits change of 0xFEA8(CS2 Value) equals to 1 bit change of 0xFE17(CS2 analog trim)? 2\how much input analog offset errors can be compensated by0xFE17 ? 3\Do...
View ArticleClik here to view.
Simulation using AD8336, AD736 and AD8551 spice models in Pspice
I have this circuit to be simulated in Pspice. I'm a complete newbie to it. But so far have managed to make the schematic (adding external components, which were not available already in the...
View ArticleIs there a way to integrate and simulate ADP5090 Model(SIMPLIS) and...
Hello, I'm new to ADIsimPE and trying to simulate a regulator circuit with current/power monitoring. This leads me to using ADP5090 for regulator and AD8210 current shunt monitor IC into a single...
View ArticleADN8831
Hello. Help solve the problem, with a thermoelectric controller ADN8831 used in an 695. Tell me the formula to determine the unknowns R1, R2, R3 for given values of the variables R(mid) R(low) R(high)...
View ArticleADN8831-EVL Heating current problem
Hi,I have set the ADN8831 EVM with the following specifications1) Tset = 25degCelcius, Tlow = 20degCelcius, Thigh = 30degCelciusVtempset = 1.25V 2) Single set point configuration...
View ArticlePower supply with multiple ground points
Hi, I've designed an SMPS with the ADP5050 IC and I want to know something: which way is better, to have each power rail with it's own ground connection (5 power rails and 5 ground connection) or all...
View ArticleADN8831-EVALZ Gerber Files
Hello, where can I download the gerber files of the ADN8831-EVALZboard. Can someone send me the files? Regards Steffen
View ArticleADM809 Reset timeout confusion
Hi, The datasheet provided here - http://www.analog.com/media/en/technical-documentation/data-sheets/ADM809-5S_-5L.pdf for ADM809 mentions that the Reset timeout is 55ms While the datasheet provided...
View ArticleADM7151 self excited
I used ADM7151 for PLL+VCO power supply ,If the load 400mA current ，then the VCO output will uperimposed spur，if don't use ADM7151, the output is correct.，attachment are ADM7151 circuit diagrams and...
View ArticleClik here to view.
When there is a negetive voltage exist on the output of ADP7142, it will not...
Hello everyone, There is a problem when I use ADP7142. When I apply a negetive voltage below -0.5V, the LDO will not work. Once the voltage over than -0.5V, the output go back to normal as the...
View ArticleCan I use ADM7150 family for precision IMU design?
Hi,I'm working on high precision IMU/AHRS using high end accelerometers, gyroscopes and magnetometers. I'm looking for best power supply chip to power these MEMS sensors to reduce noise in the circuit...
View ArticleADP225 output current spec
Hello, I would like to know if the 300mA output current specification for both outputs together or 300mA for each output. Thanks in advance,Simon.
View ArticleADP1755 Operating Temp Limit Question
For the ADP1755, page 5 of the datasheet (absolute maximum table) gives a “Junction temperature range” of -40C to +125C, then a “Junction temperature” of +150C. Is the former the operating temperature...
View Article