Can I import PSPICE models into ADIsimPE?
ADIsimPE runs on the SIMETRIX platform and supports most SPICE models, in particular PSPICE. It is able to import simulation models from many sources as described in this knowledge base posting....
View ArticleADP505X EVM Reference Schematics
Hi, Can i get Reference Schematics for ADP505X EVM. Regards,Ranganadh
View ArticleHow to add part to the library folder of ADIsimPE simulator?
I just started using ADIsimPE.I want to add AD8335 Pspice model of this part.I found the Pspice mode with .cir in the website. How to add this to the components library of the simulator?
View ArticleADM1064 'Reserved State'
Hello, Please could anyone tell me what sets of conditions could force the ADM1064 to enter the 'Reserved' state? Thank you. Regards,Phil
View ArticleADP5061/62 battery isolation FET
Hi, (1) battery isolation Vin = 0V (VBus not connected)Vbat > Vweak (system is running from battery) is it possible to isolate the battery from the system load by setting the EN_CHG & DIS_LDO...
View Articleexcel 2007 crashing
I cannot use ADIsim with excel 2007. It crashes when I open the file. Any help? The file is particular is ADP505x_BuckDesigner_Release
View ArticleADP1051 CS2 analog offset trim
Hi Sir: 1\how many bits change of 0xFEA8(CS2 Value) equals to 1 bit change of 0xFE17(CS2 analog trim)? 2\how much input analog offset errors can be compensated by0xFE17 ? 3\Do...
View ArticleADP1741ACPZ-R7 dropout voltage
Hello, For analog Devices ADP1741ACPZ-R7 the datasheet specifies the dropout voltage for conditions when Vout is 1.8V or higher as 280mV max on page 3 (although footnote 4 actually says for when Vout...
View ArticleClik here to view.
ADP5310 VFB Voltage
Dear All:I find Dataheet & User Guild For VFB1/VFB2 providingvalueisnot the same. The Datasheet Ver.0 Table2 show VFB1/VFB2 is 0.8V but UG-824 ADP5310 user guild page4 "output voltage change" show...
View ArticleClik here to view.
Simulating the ADP5052 in ADIsimPE
Hello, I would like to simulate my ADP5052 design on ADIsimPE. After selecting the SIMPLIS simulation mode, I go on Place-From AD library-Switching regulators : ADP5052 -CH1/2.The first thing I notice...
View ArticleADP5310 CH2(SW2) Question
Dear Sir:If ADP5310 SYNC/MODE=Low, this time ADP5310 Channel2(SW2) maximum output only 50mA? over 50 mA, SW2will automaticallyswitch toPWM Mode? Best Regards,Jacky
View ArticleCould I have AD8250 model file?
HiI want to do the simulation of AD8250.I made the model from "AD8250.cir" file.But I couldn't simulate that.Error message is below. *** ERROR *** The circuit is too large to simulate with this...
View ArticleADD5205 specification Fig9
Hi We would like to know the horizontal axis of Figure-9.20mSec/div?Fig-10 to 13 were also missing those data. Regardsmoto
View ArticleReconfigurable battery stack AD8280 design.
Is there a way to design a reconfigurable (i.e. via microcontroller FW and some analog switches) AD8280 design in order to implement one board for 3 to 6 cells connected in series? The number of...
View ArticleAD8000 model
ADIsimPE ver14.0.0.162 doesn't contail AD8000 model.Could you provide AD8000 model? Regards,Y.Ishii
View ArticleADP1853 theta jc
If possible, could you let me know the theta-jc of ADP1853?One of the customer wants to confirm it. Regards,
View ArticleADP5091 output current ratings
Hi All, I am interested in new IoT energy harvesting regulator ADP5091.I have one question on its output current specification.How much of output currents are available for SYS terminal and REG_OUT...
View ArticleEnergy Meter Using ADE 7753 and Arduino Uno
Hello, I am working on an energy meter project that uses ADE 7753 as energy monitor IC and Arduino Uno as MCU. I am using a voltage transformer for voltage sensing and a current transformer for current...
View ArticleWhen the ADR435 input voltage less then 7.0V
I really want to know the minimum input voltage Fengyun ADR435ARMZ? (I need 7.0 volts below the estimated base on the characteristics of the internal circuit design)Can someone give me some calculation...
View Article